A master/slave interface (option /PARALLEL) can be built into your chosen LAB-SCUBI model, for current balancing of 2 LAB-SCUBI systems in parallel connection up to 1.3MW.

Fast Dynamics and High Stability

The LAB-SCUBI provides a highly stable output of ≤0.1% rms F.S. for both current and voltage, ideal or powering sensitive DUTs. 

The high dynamics of the system allows users to switch quickly between quadrants. This is particularly useful when performing tests on bidirectional devices with fast current step changes such as super capacitors. A typical time for a 10% to 90% load step in CC mode is less than 1ms assuming an ohmic load. Example scope shots of a previous test are provided below:

Seamless Source/Sink Transition

When switching between sinking and sourcing current, the LAB-SCUBI provides a seamless transition. This means that during the quadrant change there is zero deadband time and no unwanted/disruptive behaviour is introduced to the power system's output characteristics. This feature is particularly useful for when users need to switch between charging and discharging a battery at a constant current rate, or simulate fast dynamics.

Sense Compensation

Sense terminals are built into the LAB-SCUBI for the connection of sense wire which compensates for voltage drops in the load lines. Up to 5% of the system's nominal voltage value can be compensated for. This is particularly useful for applications with long cables which have unwanted voltage drops.

Power Recycling

When functioning discharging energy storage devices, the LAB-SCUBI has an inbuilt monitoring system that synchronises with grid conditions. This recycles DC sink energy back to the grid, with typical losses of only 5-10%. 

Second Current Range (Option /SCR)

A second current range can be built into systems to give better accuracy and resolution for low current applications. This is particularly useful when testing high voltage equipment, such as electric vehicle battery packs, which typically produce low currents. The lower current range is not operable when 2 × LAB-SCUBI systems are operating in parallel.

Power Distribution Units

A PDU is used to connect the LAB-SCUBI to a DUT, when the power system is located in a different place. Both wall mounted and free standing cabinets are available. A voltmeter is included, as is an indicator light which shows the status of the insolation monitoring (turned off or active). A short-circuit switch for safe connection of a DUT when operating in quadrant 4 is available for certain models (battery simulator mode only).

Power Distribution Switch Boards

PDSB control cabinets can be provided for remotely switching the output of a single LAB-SCUBI system between separate test cells, or for connecting the two separate LAB-SCUBI systems in parallel to a nominated test cell. Up to four discharge units can also be installed in the cabinet on request.

Multiple Output Channels

If you require 2 or 4 output channels, please see our separate LAB-MOBI product family.

Internal Resistance Range

Each LAB-SCUBI is built with a user programmable internal resistance range as standard. This makes the power systems ideal for simulating the output of energy storage devices such as an ageing battery pack, fuel cell stacks and super capacitors. The exact range varies by model, for model specific details please contact us.

Switchable Output Capacitors

Output capacitance is provided to improve stability when operating in constant voltage mode. This is particularly useful to assist the fast current demands when testing drives. Some electric drives require a very stable voltage during a step change. If the voltage drop is too low it could damage the drive.

When choosing the /SIM-TEST option an extra level of capacitance is provided. Additional capacitance from an external box is also available, which can be switched between 3 different levels depending on the requirements of the test application.

Each LAB-SCUBI features constant power, constant current, constant power and internal resistance operation. As standard the power system operates in battery testing mode. This is ideal for testing battery power components and provides users with the benefits of:

• High dynamics during current changes
• Output filter with lower capacitance
• Control mode: current (CC)
• Fast current rise time
• Current ripple <0.1% f.s. rms at VDC>10VDC

Battery Simulation (Option /SIM-TEST)

Where you require to both test and emulate batteries, the system can be installed with both operating modes (/SIM-TEST), which are user switchable between the two. The battery simulation mode provides users with the benefits of:

• Low voltage dip during current transients
• Output filter with higher capacitance
• Control mode: voltage (CV)

LAB-SCUBI systems have Active Power Factor Correction (PFC) circuit integrated into the input stage as standard. This enhances the overall efficiency of the systems across the output power range when compared to a unit that does not have active PFC. In practice, this means a significant lower peak current value, a decrease of RMS value of the phase current and less perturbations of other equipment running on the same grid.

The LAB-SCUBI comes with a simple and intuitive TFT touchscreen with a menu driven interface which allows measuring and setting of V, I, P and Ri values among others. The interface provides users with the convenience of remote access when setting test values. 

Current and voltage ramps are programmable should you need to replicate a defined output for a specific research application. An event log is also provided which provides details of user actions, warnings and faults. Up to 10 named users can be specified to operate the interface with varying levels of permission, each with their own password.

Remote Control Interfaces

A CAN 2.0 interface with dbc file is provided as standard. This operates at 100Hz. The fast sampling frequency allows users to record quickly changing data, so that they can identify what’s happening at a particular point in time. A MODBUS is also provided along with VNC over Ethernet.

The VNC over Ethernet interfaces allows the touchscreen to be controlled via a PC. This feature is particulary useful for remote operation where the system may be operating in a potentially hazardous environment, or isolated from the device under test.

As standard soft tools are provided for LabVIEW integration.

Stop Button

The cabinet of the LAB-SCUBI is built with a black stop button as standard. For a complete system shutdown, an emergency stop circuit is provided which meets performance level d according to EN ISO 13849-1. A red emergency stop button is optionally available (option /E-STOP).

OVP, UVP, OCP & OTP Protection

Over voltage and over current protection limits can be adjusted to help safeguard sensitive loads. An under voltage limit can be also be user set to prevent a deep discharge which could potentially damage a battery pack.

Blocking Diode (Option /DIODE-1000)

A blocking diode is available to provide protection for the device under test against any back EMF. This is particularly useful to prevent damage to unidirectional power sources such as fuel cells. The device provides protection up to 1000A and comes in its own wheeled cabinet with 2 voltmeters to measure both sides of the diode assembly.

Discharge Unit (Option /DCU-2-500)

Discharge units are available as an additional safety feature. When the DC output is turned off, energy from the device under test will be discharged into a resistor at up to 500kW per second. This ensures that there is no residual energy on the DC link when disconnecting a device under test. This feature also works when the emergency stop button is pressed.

DC Disconnectors (Option /DC-1000A-1000V)

DC contactors are available that are linked to the safety system as standard. If the emergency stop is triggered the contactors open. They are designed to be operated under load and have an expected lifetime of 10,000 switch cycles under load.

Each LAB-SCUBI system is built for longevity. The lowest life components being the fans rated at 60,000h and electrolytic capacitors rated at 130,000h/15 years. This ensures that the systems are suitable for constant operation in long term projects.

As standard, each floorstanding LAB-SCUBI cabinet is rated to IP20. The base of each cabinet has slots in it so it can be easily moved around via pump trucks or forklifts. Cable entry is also provided via the bottom of the cabinet. The standard front to top airflow cooling system means that no distance between the wall and rear of the cabinet is required.

Cabinets builds up to IP54 are possible. On request, all cabinets can be painted in your chosen RAL colour e.g. Signal White (RAL 9003).

If your test requirement is short term, we have bidirectional DC systems in our rental range up to 216kW/2000V with battery cycling software installed.