Two G5-RSS-HC 80V modules are available in our rental range. These can be arranged in series or parallel configurations. Each module is able to operate independently, with inbuilt system comms allowing users to switch between various set-ups. 

Our rental systems can be combined in series, parallel or matrix configurations with any G5-RSS-HC modules you have previously purchased, providing they have the same nominal outputs. Up to 64 modules can be connected in this way. This allows any short term requirements outside of usual operating ranges to be met.

Fast Dynamics and High Stability

A current step between 90% sourcing to 90% sinking current can be as quick as 50µs, enabling high speed drives to be supplied. Advanced users have access to the controller settings enabling the response to be optimised for particular loads. This example shows a current step through quadrants. The upper trace shows the current transition is achieved in 50µs with a small overshoot before settling. The lower plot shows a more regulated response within 200µs. Voltage typically takes 100µs to recover within 0.5% of the set value. In multi-module systems the communication time between modules need to be considered.

Switchable Output Capacitance

Switchable capacitance is provided within each G5-RSS-HC module as standard and is used to optimise the DC filter depending on the application in which the systems are used. A low capacitance level provides fast dynamics in constant current when charging/ discharging/ cycling energy storage devices. Switching to the higher cap value provides for smoother operation during hard load steps when operating in constant voltage. Typical applications include energy storage simulation for electric drive developments.

Second Current Range

Each module features a second current range that can be built into systems to give better accuracy and resolution for low current applications. This is particularly useful when testing high voltage equipment, such as electric vehicle battery packs, which typically produce low currents.

Programmable Ripple

By utilising the embedded function generator the user can set a current ripple at up to 10kHz. The magnitude can be up to 5% of the nominal system current. Depending on the impedance of the DUT the resulting voltage ripple can be calculated. The below example shows a 10kHz ripple generated using the function generator of the G5-RSS-HC. A peak to peak current of 8A has been superimposed on a current of 100A. Alternatively, a ripple can be implemented from an external waveform generator via the analogue interface using a proportional 0-10V signal.

Sense Compensation

Sense plus terminals are built into the G5-RSS-HC for the connection of sense wire which compensates for voltage drops in the load lines. This has a number of advantages over traditional sense. It is permitted to interrupt the load line during operation (voltage on). The maximum voltage drop compensation is adjustable. The voltage difference between G5-RSS-HC output and sensing point is monitored. If a set limit is exceeded, the G5-RSS-HC unit shuts off. This is particularly useful for applications with long cables often prone to unwanted voltage drops. 

Power Recycling

When sinking energy from the unit under test the G5-RSS-HC automatically inverts the DC to AC and synchronises this output to the grid. This differs from conventional electronic loads which traditionally waste 100% of electrical energy that could be reused, by simply dissipating it as heat. By using this approach users can save significant electricity costs. Energy waste and thermal issues associated with traditional heat dissipative loads are also eliminated.

Autoranging Capability

Every G5-RSS-HC features an autoranging output. This allows many more voltage/current combinations at nominal power than a traditional bidirectional DC power system. An example of the difference is shown below using a single G5-RSS 54-1000-162 module.

Using one autoranging bidirectional PSU instead of several traditional power systems saves both cost and bench space. Despite the units offering such a large output range, they are still incredibly power dense. 54kW of output power is provided from 10U of rackmounting height.

Every module features constant current, constant voltage, constant power as standard. Adjustable internal resistance is also provided.

Internal Resistance Range

Each module is built with a user programmable internal resistance range as standard. This makes the power supplies ideal for simulating the output of energy storage devices such as battery packs, fuel cell stacks and super capacitors.

AC Cables

All rental G5-RSS-HC systems are provided with AC input cables as standard.

Active Power Factor Correction

G5-RSS-HC modules have Active Power Factor Correction (PFC) circuit integrated into the input stage as standard. This enhances the overall efficiency of the modules across the output power range when compared to a unit that does not have active PFC. In practice, this means a significant lower peak current value, a decrease of RMS value of the phase current and less perturbations of other equipment running on the same grid.

Interfaces and Control

A variety of control methods are provided. As standard each module is built with isolated analogue, CANmp, Ethernet and USB interfaces. A touchscreen HMI is also provided for front panel control and display.

Analogue Interface

An analogue interface is provided as standard which operates at 48kHz. The control port is configured as a Sub-D 25 female connector and is located on the rear panel. It allows output values to be set and read proportionally using a 0-10VDC analogue signal. Digital inputs and outputs enable various functions such as the interlock and output ON/OFF. A 10VDC reference is provided for analogue control. Digital functions are switched via a high/low signal. A 24VDC supply voltage is provided for these functions. 

Touchscreen HMI 

Each module has an HMI which provides a simple and intuitive way of control and measurement via a touchscreen panel. Users can directly access features such as the system's protections, warnings/errors and function generator without the use of a computer. A user defined passcode can be set to lock the touch screen, which prevents unauthorised access. When selected, the HMI replaces the front panel indicator.

CAN Multi-Purpose Interface

CANmp is a high speed digital interface operating at 1kHz. The interface gives users the capability to customise the CAN protocol. Up to 50 messages are user configurable. Along with the CAN ID the data length code, byte order, start bit, data type and signal factor can be adjusted by the user. A DBC file is provided and messages can be easily configured within the standard windows software. Messages can be sent cyclically or upon receipt of a sync or syncID signal.

Standard G5.CONTROL GUI

All G5-RSS-HC units come with a simple and intuitive G5.Control operating GUI as standard. Live values of the power system are displayed graphically along with any warning and error messages. The software provides a variety of second level parameters, ideal for users who like to optimise their test processes. In standard user mode the operator can remotely program set values, enable voltage output as well as the ability to analyse different variables including set and actual values via the integrated scope.

The scope function can simultaneously record up to 8 system variables. Recording can be started manually or by a defined trigger event from any variable of the system. All actual and set values (currents/voltages/power/internal resistance) can be recorded. Other recordable items include system temperatures, intermediate DC circuit, low voltage auxiliary power supplies, error related values and variables from the controller section. 

A password protected section is available to the advanced user and service technician. In addition to the standard functions the authorised user is able to:

• Program linear ramp functions at start up and set value steps during operation
• Configure multi-unit operation
• Program the PID controller parameters
• Program the unit's limit values
• Calibrate and adjust values as necessary
• Update the firmware

Function Generator

Complex DC waveforms can be implemented through the embedded function generator. The highly programmable nature of the function generator allows users to plot out exact waveforms. This is often advantageous when emulating a power device with a very specific behaviour profile. For example, when quality testing fuel cell powered equipment, the specific behaviour of a discharging fuel cell can be programmed and replicated.

As well as custom shapes, standard square, sawtooth and sine waveforms can be plotted against time. Voltage/current and voltage/power relationships can also be programmed where necessary. Parametric programming is possible, where instead of the time axis, an input variable (VIN, IIN or PIN) can be selected.

Soft Tools

An API for dotNET/C# programming is provided to simplify the integration into 3rd party control and measurements software platforms such as LabVIEW and Matlab. The API can be used to integrate into Python or remote systems based on the REST architecture.

Battery Simulation

BatSim is a battery emulation GUI for use with G5-RSS-HC power systems. The GUI allows the power supplies to simulate real world behaviour of a battery pack.

Emulating a battery pack allows specific sections of a circuit to be isolated and researched. Nearly all relevant electrical characteristics are programmable including number of cells, energy capacity, cut off limits, chemistry type and nominal voltage. The modularity of the power systems provides a convenient method to emulate different size battery stacks. Hard to replicate conditions, such as a cranking curve from a cold start can be programmed and repeated when used in conjunction with the function generator.

The multi-channel data logger provides live reporting and output to file (CSV) with timestamps. Previously recorded data can be imported, reviewed and compared in the analyser mode. Other features include:

• Adjustable internal resistance and discharge current
• Variation of exponential capacity and voltage levels
• Emulation of common battery chemistries
• Novel chemistries available on request
• Series/parallel configuration of cells

Electric Drive and Battery Cycling

Drive cycle tests can be implemented using BatControl. The GUI’s main screen provides an overview of the main test values for all BatControl operations. Live data from the connected power system is displayed, and setting/adjustment of primary values is possible. 

Previous data obtained from a test track can be imported and recreated, allowing the G5-RSS-HC to simulate a real world driving test inside a lab environment. Battery and capacitor charge/discharge profiles can also be implemented through the GUI. An internal charge counter allows users to view live data for Wh and Ah. Energy storage orientated tests which users can program include: 

• Battery charge/discharge cycles
• Automated drive cycle loading and simulation
• Fuel cell loading
• Comparative studies
• Shot and burst overload tests
• System degradation tests
• Battery lifetime tests

Solar Array Simulation

SASControl software has all EN 50530 tests pre-installed, with minor adaptations possible for particular inverter models. The GUI allows users to edit irradiance, temperature, amplitude values or input scaling with special commands. 

Previous tests have been conducted using over 400,000 individual data points, with more possible. This allows users to simulate changing conditions over the course of day.

When renting 2x G5-RSS-HC modules a cabinet integration is used to make deployment simpler, quicker and safer in master/slave. Among the cabinet safety features is a status indicator that alerts users of any residual energy on the DC link that is greater than 30V. This operates even if the mains power is turned off. Another indicator assesses the quality and correct rotation of the AC input voltage and illuminates if correct.

Key features include:

• All 4 Heavy Duty Castors with Locking Function
• Indication of Connected AC Line Voltage
• Passive Indication of DC Output Voltage
• Panel Mounted Emergency Stop
• CEE125 Plug with 5m AC Input Cable (3L + PE +N)

A separate flight case is available when renting a single module. Contact ETPS for more details.

If you are looking to purchase a system, new G5-RSS-HC modules can be found in our Bidirectional DC range. New undirectional DC source only variants can be found in the G5-SOURCE product family.